Data fields represent, in order: heading, magnetic field status, pitch, pitch status, roll, and roll status. The communications will take place at a much higher speed, however. Hello, Your privacy is important to us. Connection of any device s to a communicating bus of a Honeywell security system e. At this time, the meter reading should jump to approximately 12 volts for few seconds and then return to zero. I chopped an old telephone cable in half and soldered the capacitors in place with alligator clips for the power and resistor as I was not sure which values I would need, the resistor could be soldered in place now that I know it works with my modem.
The control will automatically return to normal alarm system function when the downloading session is completed. I confuse the yellow loose crocodile clips and the loose green crocodile clip … On the other hand, do not feed the cable with positive and negatrivo of the panel as in the case of Watelco cable? This value is the difference between the raw tilt measurements normalized, linearized, and filtered according to parameter settings. No password or user name is required to review these manuals. If you are up for some tinkering you can make a capacitive coupling cable below which will allow you to use a lot more of the Hayes Smartmodem products. Wire Red and Green to the panel's phone terminals.
To make edits to a panels configuration or even connect to a panel you need to create a customer account for that panel. Our magnetic sensors are designed to accurately detect the direction and magnitude of external magnetic fields for compassing, magnetometry and positioning applications. Click the connection icon next to the save button and the below dialog will open up. These are highly reliable, top performance products that are delivered when promised. The three colored terminals red, blue, and white must be left uncut for direct-wire downloading applications. No voltage should be seen at this time. Dear Sirs, I have one request.
You will also need a computer that is compatible with the Compass software. To check the software, proceed as follows: 2. Connect a jumper wire from Tip terminal 23 to terminal 4 Aux Power negative. Red on Ring terminal 24 , Green on Tip terminal 23. Click the connect button in the Honeywell compass software and the modem will connect to the panel. Processor, memory, and disk space requirements are minimal.
There is limited information on the internet about it so I decided to help others out who want to go down this path. Customer understands that a properly installed and maintained alarm system may only reduce the risk of a burglary, robbery, fire, or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result. Make sure you do not buy a null-modem cables these are wired with the receive and transmit lines crossed for direct computer to computer connection. It doesn't have to be Total Connect, but the AlarmNet dealer would have to activate some sort of service. There is were you activate the connection to the panel. Here are all the values I tested below and they all worked.
To do so, you will need an approved modem for use with Compass. I also have downloaded and installed Compass2. The configuration show will be the default configuration as you have not retrieved uploaded the current configuration from the panel yet. This software is designed for professionals to store the configurations of all the installations they have done. How can I add this panel to its list. See note 3 below for details. Insert the Null Modem adapter supplied and try again.
The setup to program these panels through the Honeywell Compass software is bulky and a bit of a mess as it requires far obsolete technology such as dial-up modems. You make it entertaining and you still care for to keep it wise. This is actually a tremendous site. I spent hours trying to get this to work but ultimately could never get to work with my Hayes SmartModem Optima 9600. Compass is not intended for the end user and is only distributed to Honeywell dealers. Inquiry, I am not clear the connection of the capacitive cable … The capacitors of.
Through the modem, the software will connect to the control panel, as if the connection were taking place over a phone line. Seller shall have no obligation under this Limited Warranty or otherwise if the product s is altered or improperly repaired or serviced by anyone other than Honeywell factory service. This was a huge issue for me as I bought a Hayes SmartModem Optima 9600 which is in the supported modem document but not listed in the software and probably took over 10 hours of tinkering with the whole setup to get it to work, save the hassle and buy a , from Ebay. From the basic magnetic heading, a declination value may be added to arrive at a geographic north referenced heading. As for Compass, we don't support end users connecting with Compass so you would have to talk to your alarm company about that. Instead of using a keypad hooked up to your , you can use the Compass software to configure all programming settings and then download the settings to the alarm control panel. Let me start by stating you really should not go down the path of trying to program a security panel with the Honeywell Compass software unless there is a specific need as you will spend more time setting up and getting the software working than programming the panel through the keypad.
. This warranty replaces any previous warranties and is the only warranty made by Seller on this product s. If this does not occur, there is a possibility that the transmit and receive pins on the computer are reversed. At the other end of this cord, you'll have 4 flying leads, Black, Yellow, Red, and Green. The next screen you will see is this, it is the main screen of the compass software. Using Compass Software Let the fun begin, once you have all the equipment needed to connect to your panel you need to setup the Honeywell compass software. It is sufficient to connect the pins listed in Table 1 for most applications.